|Place of Origin:||Japan|
|Minimum Order Quantity:||1pcs|
|Price:||USD 4-4.5/ PCS|
|Size:||2.6 Inch||Resolution:||240(RGB)×400 (WQVGA) 180PPI|
|Interface:||Parallel RGB (1 Ch, 4-bit)||Connect Type:||0.3mm 29 Pins FPC|
|Color Depth:||262K 72% NTSC||Screen Type:||LCM , CG-Silicon|
|Treatment:||Hard Coating (3H)||Arrangement:||(RGB) Vertical Stripe|
|Work Mode:||ASV, Normally Black, Transflective||Viewing Direction:||80/80/80/80 (Typ.)(CR≥5)|
262K Color TFT LCD Displays,
2.6inch TFT LCD Displays,
Parallel RGB TFT LCD Screen
Sharp LS026B8PX04 Parallel RGB Interface 2.6inch 262K Color TFT LCD Displays
The LS026B8PX04 is a 2.6 inch diagonal CG-Silicon display panel product from Sharp Corporation (hereafter called Sharp), with an integral WLED backlight system, without backlight driver, without touch screen. It features an operating temperature range of -10 ~ 60°C , a storage temperature range of -20 ~ 70°C . It's general features are summarized by Adia in the following: Portrait type, Transflective, WLED Backlight, U/D,L/R Reverse . Based on its features, Adia recommend that this model be applied to Mobile Phone etc.
3.Low Power consumption, Wide view angle,High trans, High CR.
4.Thin and light weight
Mainly used in car rearview mirror and MP4/MP5 etc.
|2||Panel Type||ASV, Normally Black, Transflective||-||-|
|3||Resolution||240(RGB)×400 (WQVGA) 180PPI||pixel||-|
|4||Color Depth||262K 72% NTSC||-||-|
|5||Good View at||Symmetry||-||Note|
|6||Viewing Angle||80/80/80/80 (Typ.)(CR≥5)||-||-|
|7||Contrast Ratio||330 : 1 (Typ.) (TM) 10:1 (Typ.) (RF)||-||-|
|9||Module Size||40.6(W) ×67.5( L) ×1.47(T)||mm||Note|
|10||Active Area||33.84 × 56.4 (H×V)||mm||-|
|14||Response||13/30 (Typ.)(Tr/Td) ms||bit||-|
|15||Backlight||1S5P WLED , No Driver||-||-|
|16||Interface||Parallel RGB (1 ch, 4-bit) , 29 pins FPC||-||-|
Outline Dimension (unit: mm)
1.1.Polarizer Cleaning, Petroleum ether (or N-hexane) is recommended for cleaning the front/rear polarizers and reflectors, acetone, toluene and ethanol are not allowed to avoid damaging the surface.
1.2. Body grounding, must wear Anti-ESD wrist strap while pick up LCDs.
1.3. FPC Soldering, less than 300℃/3S, solder must be grounding on grounding bench.
1.4. If use electric Screwdriver to do assembly, screwdriver must be grounding.
2.1. Keep in a sealed polyethylene bag.
2.2. Keep in a dark place.
2.3. Keep in temperature between 0°C and 35°C.
NOT allowed at 70°C for more than 160 Hours, or at -20°C for more than 48 Hrs.
If liquid crystal leak out of a damaged glass cell, DO NOT put it in your mouth or touch eyes, if the liquid crystal touch your skin or clothes, please wash it off immediately using soap and water.
Unless otherwise agreed between ADIA and customer, ADIA will replace or repair any of its LCD modules which are found to be functionally defective when inspected in accordance with ADIA LCD acceptance standards (copies available upon request) for a period of one year from date of shipments. Cosmetic/visual defects over specs must be returned to ADIA within 30 days of shipment. Confirmation of such date shall be based on freight documents. The warranty liability of ADIA limited to repair and/or replacement on the terms set forth above. ADIA shall not be responsible for any subsequent or consequential events.
4.1RETURNING LCM UNDER WARRANTY – TERMS AND CONDITIONS
4.1.No warranty can be granted if the precautions stated above have been disregarded. The typical examples of violations are :
- Broken LCD glass.
- Circuit modified in any way, including addition of components.
4.2.Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with sufficient description of the failures or defects. Any connectors or cable installed by the customer must be removed completely without damaging the PCB’s eyelet, conductors and terminals.
Q1. How can I trust your product quality?
--Our Raw materials are all ROHS compliant .
--Display is an ISO9001:2008 and ISO9001:2015 Certified company, we’ve been adhering to the ISO standards strictly in our production.
--Our products are 100% Visual and Function test before shipments.
Meanwhile, we do necessary Aging test and Reliability tests to our TFT Display modules, eg. Store and Operate in High and Low Temperature & High Humidity Environment, ESD and anti-interference test , Drop(with package) and Vibration Test.
Our Touch Screens goes through Salt spray test, Hardness test, Steel ball Drop test, Flatness test, Thermal shock test…
--Our experience and proficiency make the qualification rate always being 99.7% or above.
Contact Person: Joe Chen